Beko Dishwasher Drain Pump Running Continuously: How to Stop It

Is your Beko dishwasher drain pump running non-stop? Don't panic, we've got you covered!

In this article, we'll show you how to put an end to this frustrating issue. We'll dive into the possible causes of the continuous drain pump operation, guide you through checking for blockages, testing the pump for malfunctions, and even resetting the control panel.

By following these steps, you'll regain control and stop that drain pump from running like there's no tomorrow.

Let's get started!

Key Takeaways

• Possible causes of a Beko dishwasher drain pump running continuously include a clogged or partially blocked drain hose or filter, a malfunctioning float switch, a malfunctioning control board, or lack of dishwasher maintenance and care.
• To check for blockages in the drain system, inspect the drain hose for kinks, twists, or clogs, ensure proper connection of the drain hose to the dishwasher and drain pipe, use a long, flexible brush or pipe cleaner to remove blockages, and remove and rinse the filter to remove debris or food particles. Replace a damaged or worn-out filter.
• Testing the drain pump for malfunction involves checking for continuous running of the drain pump, improper water drainage, and strange noises during the draining cycle. Check for clogs or debris in the drain pump, and consider replacing the drain pump if necessary.
• To reset the dishwasher's control panel, press the 'Cancel' button for 3 seconds, wait for the dishwasher to reset, and test the dishwasher by running a new cycle to ensure proper functioning. This can help resolve common dishwasher problems. Contact Beko Customer Support for further assistance by reaching out to them through their official website, providing detailed information about the issue, and having the model number and serial number ready for effective assistance.

Possible Causes of a Beko Dishwasher Drain Pump Running Continuously

You might be wondering what could be causing your Beko dishwasher drain pump to run continuously. Understanding the possible causes of this issue is crucial in troubleshooting common dishwasher problems.

There are several factors that can lead to a continuous running drain pump. First, check if the dishwasher is draining properly. A clogged or partially blocked drain hose or filter can cause the pump to run continuously as it tries to remove the water. Inspect these components and clean or replace them if necessary.

Additionally, a malfunctioning float switch can also be the culprit. The float switch is responsible for detecting the water level in the dishwasher. If it gets stuck or becomes faulty, it may send a continuous signal to the drain pump, causing it to run non-stop.

Lastly, a malfunctioning control board can also be the reason behind the continuous running drain pump. If the control board isn't functioning properly, it may send incorrect signals to the drain pump, making it run continuously.

Understanding dishwasher maintenance and care is essential in preventing these issues. Regularly cleaning the filters, drain hose, and inspecting the float switch can help avoid a continuously running drain pump.

Checking for Blockages in the Drain System

Take a flashlight and carefully inspect the drain hose and filter for any possible blockages. Blockages in the drain system can cause your Beko dishwasher drain pump to run continuously.

Here are three steps to help you troubleshoot and address common drainage issues:

1. Check the drain hose: Start by inspecting the drain hose for any kinks, twists, or clogs. Make sure the hose is properly connected to both the dishwasher and the drain pipe. If you find any blockages, use a long, flexible brush or pipe cleaner to remove them.
2. Examine the filter: Locate the dishwasher's filter, which is typically at the bottom of the tub. Remove the filter and rinse it under running water to remove any debris or food particles. If the filter is damaged or worn out, replace it with a new one.
3. Clear the air gap: Some dishwashers have an air gap installed on the sink or countertop. This prevents wastewater from flowing back into the dishwasher. Check the air gap for any obstructions and clean it thoroughly. If necessary, remove the cap and clean the inside as well.

Regular maintenance is crucial for the proper functioning of your dishwasher's drainage system. By following these troubleshooting steps and performing routine maintenance, you can prevent blockages and ensure efficient drainage.

Testing the Drain Pump for Malfunction

Before proceeding with any repairs, it is important to test the drain pump for malfunction to accurately diagnose the issue with your Beko dishwasher. Troubleshooting the drain pump can help identify if it is the root cause of the continuous running. Here are some key signs of a faulty drain pump:

Signs of a Faulty Drain Pump	Troubleshooting Tips
The drain pump runs continuously, even when the dishwasher is not in use.	Check if the drain pump is clogged or blocked by debris. Remove any obstructions and try running the dishwasher again.
The dishwasher does not drain water properly, leaving dishes wet or dirty.	Inspect the drain pump for any damage or wear. Replace the pump if necessary.
Strange noises coming from the dishwasher, particularly during the draining cycle.	Test the drain pump by manually activating it. If it produces unusual sounds, it may need to be replaced.

To test the drain pump, follow these steps:

1. Disconnect the dishwasher from the power supply.
2. Locate the drain pump, usually located at the bottom of the dishwasher.
3. Remove any cover or protective plate to access the pump.
4. Carefully inspect the pump for any visible signs of damage or blockages.

Resetting the Dishwasher's Control Panel

To reset your dishwasher's control panel, try pressing the 'Cancel' button for 3 seconds to stop any ongoing cycles. This can help resolve common dishwasher problems and is an effective troubleshooting method.

Here are three steps to follow when resetting the control panel:

1. Press the 'Cancel' button: Locate the 'Cancel' button on the control panel, usually marked with a large 'X' or a 'Cancel' label. Firmly press and hold this button for 3 seconds until you hear a beep or see the display go blank.
2. Wait for the reset: After pressing the 'Cancel' button, give the dishwasher a few moments to reset. It may take a short while for the control panel to restart and for any ongoing cycles to stop completely.
3. Test the dishwasher: Once the dishwasher has reset, try running a new cycle to see if the issue has been resolved. Select a program, close the door, and press the 'Start' button to begin the cycle. Observe the dishwasher's operation to ensure that it's functioning properly.

Contacting Beko Customer Support for Further Assistance

If you're experiencing continued issues with your Beko dishwasher, you can reach out to Beko Customer Support for further assistance. Contacting customer service is an effective way to resolve any persistent problems you may be facing with your appliance. The dedicated team at Beko is knowledgeable and experienced in troubleshooting dishwasher issues, and they can provide you with the necessary guidance to resolve the problem.

When contacting Beko Customer Support, be prepared to provide them with detailed information about the issue you're experiencing. This will help them understand the problem better and provide you with accurate troubleshooting tips. It's important to describe the issue as precisely as possible, including any error codes or unusual behaviors your dishwasher is displaying.

To contact Beko Customer Support, you can visit their official website and look for the contact information. They may have a dedicated phone line or email address specifically for customer support. When reaching out, be sure to have your dishwasher's model number and serial number handy, as they may ask for this information to assist you more effectively.

Frequently Asked Questions

How Can I Determine if the Drain Pump in My Beko Dishwasher Is Running Continuously?

To determine if your Beko dishwasher's drain pump is running continuously, listen for a constant noise coming from the machine. If you hear it, follow these steps to fix the noisy drain pump and clean the drain pump filter.

What Are Some Common Signs of Blockages in the Drain System of a Beko Dishwasher?

If your Beko dishwasher is experiencing blockages in the drain system, there are common signs to look out for. To fix this issue, you can follow these steps to ensure smooth functioning and liberation from the problem.

Can a Malfunctioning Drain Pump Cause Other Issues in My Beko Dishwasher?

A malfunctioning drain pump can have negative effects on your Beko dishwasher's performance. It can cause drainage issues and potentially lead to other problems. Troubleshooting the drainage system is crucial to resolve these issues.

Is There a Specific Button or Combination of Buttons on the Dishwasher's Control Panel That Can Be Used to Reset It?

To reset your dishwasher control panel and troubleshoot drain pump issues, press and hold the "Reset" button for 10 seconds. This will liberate your appliance from its continuous drain pump cycle and restore its functionality.

What Should I Do if I Have Tried All the Troubleshooting Steps and the Drain Pump in My Beko Dishwasher Is Still Running Continuously?

If you've exhausted all troubleshooting steps and the drain pump in your Beko dishwasher is still running continuously, you may need to consider resetting the dishwasher or replacing the drain pump.