GE 2 Device Universal Remote Control Codes work with Simple Television Hubs through direct entry during programming. The primary codes for Samsung and LG hubs are 0105 and 0004 respectively.
Additional codes cover other brands in the aggregated data. Users locate the correct code by testing entries until the hub responds to power commands. This approach avoids trial and error beyond the listed options.
GE Codes for Television Hub Brands
The master data table aggregates codes from GE documentation for common television hub brands. Each entry lists multiple options to increase success rates during setup. Testing starts with the first code in the series for each brand. Verification occurs by sending a power command after entry. The table supports quick reference without external lookups.
| Television Brand | Primary Code | Secondary Code | Tertiary Code |
|---|---|---|---|
| Samsung | 0105 | 0004 | 0005 |
| LG | 0004 | 0050 | 0156 |
| Sony | 0000 | 0111 | 0128 |
| Vizio | 0178 | 0171 | 0128 |
| TCL | 1243 | 1343 | 1431 |
| Sharp | 0009 | 0226 | 0263 |
Codes appear in order of reported success frequency. Multiple entries allow fallback when the first fails to register.
GE Remote Code Compatibility by Brand
Analysis shows that codes for Samsung hubs achieve the highest compatibility rates across tested models. LG entries require the secondary code more often than others. Sony series respond best to the initial listed value in most cases. Vizio and TCL follow similar patterns with occasional need for the third option. This data comes from aggregated user reports and manufacturer lists.
Samsung codes maintain consistency even on older hub firmware versions. LG options show slight variation based on screen size categories. Cross brand testing confirms no overlap between primary values in the table.
Manage Remote Setup Logistics Efficiently
Setup logistics require the remote in pairing mode before code entry begins. Power the television hub first and point the remote directly at the sensor. Hold the setup button until the indicator light stays on. Release and input the four digit code from the table within ten seconds. The light turns off to confirm acceptance.
Repeat the process for a second device if needed on the same remote. Store the remote away from direct sunlight to preserve button function. Test all basic commands after programming completes.
GE Codes for Sony Television Hubs
Sony television series accept the primary code in most standard hub configurations. Users power on the device and enter setup mode on the remote first. The indicator responds with a steady light when ready for digits. Input 0000 and wait for confirmation before testing volume controls. Secondary codes apply when the hub uses extended firmware updates.
Series from the Bravia line follow the same entry sequence without extra steps. Older models may need the third code listed in the table for full function.
GE Remote Codes for Vizio Hub Issues
Vizio hub code failures often trace to timing errors during entry rather than incorrect values. Reset the remote by removing batteries for thirty seconds before retry. Select the secondary code 0171 next and repeat the setup sequence exactly. Confirm the hub sensor remains unobstructed throughout the process.
Users report higher success after clearing nearby wireless interference sources. The tertiary code serves as final option before seeking replacement hardware.
GE Codes for TCL Smart Hubs
TCL smart hubs require the primary code 1243 for initial programming attempts. Activate setup mode and enter digits without pauses between numbers. The remote light signals acceptance when the hub powers off on command. Switch to secondary code 1343 if the first attempt times out.
Smart hub models integrate these codes without additional app intervention. Verification includes checking input source buttons after power tests pass.
GE Codes for Simple Television Hubs
Retrieve the master data table for reference. Power the target hub and enter setup on the remote. Input the selected code from the brand row. Test the power function to confirm operation. Repeat for any secondary device on the same remote unit.
Hey, I’m Jake. I focus on cooling systems at Appliance Mastery, like fridges, freezers, and air conditioners.
I’ve worked in appliance repair for more than ten years and I’m certified through NASTeC. I’ve seen just about every fridge issue you can imagine.
My goal is to help you fix problems without stress. Whether it’s a freezer that won’t cool or an AC that keeps beeping, I’m here to walk you through it.