How Do I Fix My Dishwasher Control Board

Are you tired of struggling with a malfunctioning dishwasher control board? Maybe the buttons aren’t responding or the display is showing error codes. Whatever the issue may be, dealing with a broken control board can be frustrating and time-consuming.

Not only does it disrupt your daily routine, but it also puts a dent in your wallet if you decide to hire a professional repair service. But what if I told you that fixing your dishwasher control board is not as complicated as you think?

In this article, we will explore some common problems that can occur with your dishwasher control board and provide step-by-step instructions on how to fix them yourself. Say goodbye to the hassle of dealing with a faulty appliance and hello to a fully functioning dishwasher once again!

Common Signs of a Faulty Dishwasher Control Board

What is a dishwasher control board?

A dishwasher control board is also known as an electronic control board. It manages and controls the dishwasher’s functions, such as water temperature, cycle selection, and duration. The control board can be programmed to work with various dishwashing cycles, depending on the model of the dishwasher.

Signs that your dishwasher control board is faulty:

• The dishwasher does not turn on or respond when you press the buttons.
• The display screen shows incorrect information or does not light up at all.
• The dishwasher stops mid-cycle without any warning.
• You notice unusual smells emanating from the machine or burning smells coming from the control board area.
• The machine overflows with water during operation.

If you observe any of these signs in your dishwasher, it may be time to replace your old control board with a new one.

How to Diagnose Problems with Your Dishwasher Control Board

To determine if your dishwasher’s electronic control board is faulty, you will need to conduct some troubleshooting tests:

Check Power Supply

Firstly, check that your appliance has power supply. Ensure that the circuit breaker hasn’t tripped and that there are no damages to wires or plugs around the power source.

Inspect Control Board Wires and Connectors

Secondly, inspect the wires on the back of the control panel for any loose connections. If everything appears connected appropriately, remove each connector from its respective switch and touch together.

If there are no visible faults or issues observed in both checks above, then replacing a new control board may be required.

DIY or Hire a Professional: Fixing Your Dishwasher Control Board

Should I attempt to replace the control board myself?

Replacing a dishwasher control board may require technical knowledge. If you have experience in electrical repairs, you can opt for the DIY route.

However, if you lack technical knowledge or are not comfortable working with electrical appliances, it is best to hire a professional repair technician. A licensed technician will ensure that your dishwasher and its new control board are installed safely and correctly.

Tools and Equipment Needed to Fix Your Dishwasher Control Board

If you choose to do it yourself, below are some of the tools and equipment required for replacing your dishwasher’s electronic control board:

• Screwdriver set (may vary depending on your model’s screws)
• Multi-meter tool
• New electronic control board
• Pliers
• Crimping tool

Click here to preview your posts with PRO themes ››

Removing the Old Control Board from Your Dishwasher

Before installing a new control board, remove the old one by following these steps:

1. Disconnect power supply: Turn off power from the circuit breaker and unplug your appliance from its power source.
2. Remove console panel: Remove screws holding the console panel in place. Some models may need additional parts removed before accessing the electronic control board.
3. Note down wire connections: Before removing wires connected to the old control board, take note of where each wire goes. You can use masking tape or labels as markers.
4. Remove connectors: Use pliers or crimpers to remove each connector from their respective switch.
5. Remove old control board: Unscrew any screws holding the old control board in place and gently remove it from its position.

Finding a Replacement Control Board for Your Dishwasher and Its Cost

You can find a replacement control board for your dishwasher at an appliance parts store, online retailer or authorized dealer.

The cost of the new part will depend on the model of your dishwasher and the severity of the damage to your old control board. On average, you can expect to spend between $100 to $200 on a new electronic control board.

Installing the New Control Board in Your Dishwasher and Precautions to Take

Once you have purchased a new control board, install it by following these steps:

1. Attach wiring: Connect each wire connector based on the notes taken before removing the old control board.
2. Secure new control board: Place the new control board into its appropriate position and screw it in place.
3. Reattach console panel: Replace any additional parts removed earlier before reattaching screws holding the console panel in place.
4. Restore power supply: Plug your appliance back into its power source and switch power supply back on from circuit breaker.

Before turning on your dishwasher, double-check that all connections are secure and that there are no loose wires.

Safety precautions:

• Always turn off power from the circuit breaker before attempting to fix electronic appliances.
• Avoid touching wires with wet hands or standing in water while fixing electrical appliances.
• If unsure about any step during installation or repair, seek assistance from a professional technician.

Testing the New Control Board to Ensure Proper Functionality

After replacing your dishwasher’s electronic control board, test your appliance to ensure that it is working correctly.

Turn on your dishwasher and select a cycle. Observe the machine for any unusual sounds or smells. Confirm that water is flowing in and out of the machine correctly. Check if the display screen shows accurate information.

Click here to preview your posts with PRO themes ››

If you notice any issues during testing, disconnect power supply and recheck all connections to ensure they are secure and free from damages.

If everything appears to be functioning well, congratulations! You have successfully replaced your dishwasher’s control board.

In conclusion, fixing a dishwasher control board can be done by following some simple steps. It is important to ensure that the power supply is turned off and to carefully remove and inspect the control board for any visible damage or defects. If necessary, replacement parts can be purchased and installed to restore the dishwasher’s functionality.

Frequently Asked Questions about How Do I Fix My Dishwasher Control Board

Is it worth it to replace a dishwasher control panel?
When the cost of repair is 50% or more than the cost of a new unit, it is recommended to replace the old unit. For instance, if getting a new dishwasher would cost $500, you should not spend over $250 on repairs. Additionally, if you have had to repair your dishwasher several times in the past year, it may be time to consider getting a new one.

How much does it cost to replace a control board on a dishwasher?
The typical cost of repairing a dishwasher control panel ranges from $150 to $350, and the expense depends on the specific issue. The control panel is an important component of the dishwasher, as it manages tasks such as setting the time and temperature. A malfunctioning or broken control panel can render the appliance inoperable.

How do you diagnose a bad control board?
To check if the power in the line is working, use a voltage meter. If the meter reads 120 volts AC when connected to the wire on your board, then the power is functioning properly. The indicator light on the board should also light up when receiving power, but if it does not, it is time to replace the board.

Why do appliance control boards fail?
An electrical power surge is a common cause of electronic oven control board failure, often caused by lightning strikes during storms. Other causes include power outages, electrical grid overloads, utility service provider load shifting, and wind storms.

Is a 10 year old dishwasher worth fixing?
If your device is only a few years old and the cost of repairing it is less than half of the cost of getting a new one, then it’s best to repair it. However, if the repair cost is more than half of the cost of a new device, or if your device is already 7-10 years old, then it’s better to get a new model.

Can a control panel on a dishwasher be replaced?
Luckily, it’s easy to replace a dishwasher panel and restore the appliance’s original look. You can even switch up the color of the dishwasher by buying a new panel that matches your other appliances or kitchen décor.