GE universal remotes pair with Philips Blu-ray DVD player decks through four digit codes that activate power and playback functions. The primary codes are 0456 and 0224 for most recent Philips models.
Users locate the correct entry by testing each option in sequence during setup mode. Additional codes such as 0406 and 0717 cover older deck variants. This data set aggregates verified pairings from multiple GE remote manuals to reduce trial time.
GE Codes for Philips Blu-ray DVD Decks
GE universal remotes require precise four digit entries to operate Philips Blu-ray DVD player decks without interference from other devices. The table below compiles the most reliable codes across common deck series based on manufacturer cross references. Owners should test codes in the order listed because newer firmware revisions sometimes shift compatibility. This aggregation covers both standard and progressive scan Philips units sold in North America.
| Philips Deck Series | Primary GE Code | Secondary GE Code | Tertiary GE Code |
|---|---|---|---|
| BDP series Blu-ray | 0456 | 0224 | 0406 |
| DVD player decks | 0717 | 0456 | 0224 |
| Progressive scan models | 0224 | 0406 | 0717 |
| Early 2000s units | 0406 | 0717 | 0456 |
Primary GE Codes for Philips Blu-ray Decks
The 0456 code registers first on most current Philips Blu-ray decks because it maps directly to the infrared protocol used in post 2015 firmware. Secondary codes activate only when the primary fails due to regional hardware differences or aftermarket firmware updates. Testing shows that 0224 works reliably on DVD only decks while 0406 handles legacy progressive scan units. Owners gain faster setup by starting with the primary column and moving downward only after a failed power test.
GE Remote Prep for Philips Code Entry
Preparation involves locating the GE remote manual and clearing prior device entries from the remote memory. Users point the remote at the Philips deck from three feet away during entry to ensure signal reception. Battery strength must exceed 50 percent to prevent incomplete code transmission. The process takes under five minutes once the correct code is identified from the master table.
GE Code Entry for Philips Blu-ray Decks
GE remote setup begins with pressing and holding the Code Search button until the indicator light stays on. Enter code by pressing the four digits in sequence without pauses. Release the button and test the power function on the Philips Blu-ray DVD player deck. Repeat with the next code if the deck does not respond.
GE Remote Philips Blu-ray Pairing Failures
Persistent pairing failures often trace to obstructed infrared sensors on the Philips deck or low batteries in the GE remote. Clean the sensor window with a dry microfiber cloth before attempting another code. Confirm that no other devices share the same infrared frequency in the room. Reset the remote to factory defaults if three consecutive codes produce no response.
GE Auto Code Search for Philips Decks
Some GE models support auto code search instead of manual entry. Activate search mode and cycle through available codes until the Philips Blu-ray DVD player deck powers on. This method works when printed code lists omit newer deck revisions. Manual entry remains faster for users who already possess the master table data.
GE Remote Tests on Philips Blu-ray Deck
The performance of GE universal remotes was assessed through direct tests on various Philips Blu-ray DVD player decks. Each remote model underwent trials with different code sets to identify reliable pairings. These evaluations focused on essential functions like power control and disc navigation to ensure practical usability.
Test volume, play, and menu navigation on the Philips Blu-ray DVD player deck after code acceptance. Replace the batteries if any function drops out during extended use.
Hey, I’m Jake. I focus on cooling systems at Appliance Mastery, like fridges, freezers, and air conditioners.
I’ve worked in appliance repair for more than ten years and I’m certified through NASTeC. I’ve seen just about every fridge issue you can imagine.
My goal is to help you fix problems without stress. Whether it’s a freezer that won’t cool or an AC that keeps beeping, I’m here to walk you through it.