The reset button on the Frigidaire FRSS2623AS ice maker sits on the side of the module inside the freezer compartment. Press it after a 30 second power cycle to clear most sensor faults and restart ice production. Owners who still see no output must then check the water inlet line and confirm the freezer holds a steady temperature below zero degrees Fahrenheit.
Locate Frigidaire FRSS2623AS Ice Maker Reset Button
The Frigidaire FRSS2623AS positions the reset button on the right side panel of the ice maker assembly. Access requires removal of the ice storage bin to expose the module fully. This placement keeps the button near the optical sensor for quick activation during troubleshooting. Technicians reach it without tools in most cases once the bin clears the path. The button activates the control board reset sequence when held for several seconds.
Check Frigidaire FRSS2623AS Symptom Table
Before attempting any reset procedures on your Frigidaire FRSS2623AS ice maker it helps to review the symptom table first. This table outlines common issues and their likely causes for this specific refrigerator model. Matching your observations to the listed symptoms allows for a more targeted approach to troubleshooting.
Owners first match observed problems to common causes before any disassembly. The table below narrows the primary suspect and rates repair difficulty on a simple scale. Accurate matching prevents unnecessary part orders and shortens downtime.
| Symptom | Primary Suspect | Difficulty 1-5 |
|---|---|---|
| No ice at all | Frozen fill tube | 2 |
| Slow production | Low water pressure | 3 |
| Ice cubes too small | Warm freezer air | 1 |
| Harvest cycle fails | Faulty sensor | 4 |
Frigidaire FRSS2623AS Sensor Valve and Board Causes
The Frigidaire FRSS2623AS ice maker stops when the optical sensor detects a blockage or when the water valve receives no signal. Power surges or brief outages often trip the internal board and leave the unit in standby mode. Temperature swings above zero degrees Fahrenheit also halt the harvest motor mid cycle. These three factors account for the majority of service calls on this model series.
Frigidaire FRSS2623AS Ice Maker Reset Sequence
Remove the ice bin from the freezer compartment first. Locate the reset button on the module side panel. Press and hold the button for five seconds after the unit has sat unplugged for thirty seconds. Reinstall the bin and restore power to test production within two hours. Monitor the first cycle to confirm water flows into the mold tray without overflow.
Frigidaire FRSS2623AS Inlet Valve Pressure Test
The inlet valve on the Frigidaire FRSS2623AS sits at the rear of the refrigerator near the water line connection. Low household pressure below 30 psi prevents the valve from opening fully during fill stages. Shut off the supply and detach the line to clear any debris from the screen filter. Reattach and restore flow while listening for the valve solenoid click during the next cycle.
Frigidaire FRSS2623AS Freezer Temperature Requirements
Freezer air must remain at or below zero degrees Fahrenheit for consistent ice formation on this model. Warm spots near the ice maker often result from blocked vents or overloaded shelves that restrict airflow. Adjust the thermostat dial one notch colder and wait four hours before rechecking with a separate thermometer. Consistent readings eliminate temperature as the hidden cause of stalled production.
Frigidaire FRSS2623AS Optical Sensor Obstruction Test
The optical sensor on the Frigidaire FRSS2623AS sits beside the reset button and detects ice levels in the bin. Frost buildup or stray ice fragments block the beam and trigger a false full signal. Wipe the sensor lenses with a dry cloth after bin removal. Clear any visible debris from the emitter and receiver faces before reinstalling the bin.
Replace Frigidaire FRSS2623AS Ice Maker Module
Persistent failures after reset and valve checks require module replacement. Order the correct assembly for the FRSS2623AS series through authorized parts channels. Disconnect the wiring harness and unclip the old unit from its mounting brackets. Install the new module and press the reset button once power returns to initialize the board.
Hey, I’m Jake. I focus on cooling systems at Appliance Mastery, like fridges, freezers, and air conditioners.
I’ve worked in appliance repair for more than ten years and I’m certified through NASTeC. I’ve seen just about every fridge issue you can imagine.
My goal is to help you fix problems without stress. Whether it’s a freezer that won’t cool or an AC that keeps beeping, I’m here to walk you through it.