Fault code 353 on the GE Profile washer dryer combo signals an inverter board malfunction. Replacing the inverter board assembly corrects the error code in most instances.
Technicians trace the issue to failed power regulation within the board itself. Testing the board output confirms whether replacement is necessary rather than a simple reset. This approach avoids unnecessary repairs on other components like the main control board.
Examine Symptoms of Code 353
The GE Profile washer dryer combo displays fault code 353 when the inverter board stops communicating properly with the motor. This symptom often appears during spin cycles or when the unit attempts to change speeds. Users notice the machine stops mid cycle and shows the code on the display panel. Further inspection reveals no response from the drive motor despite power reaching the unit. Voltage checks at the board terminals help narrow the fault quickly.
| Symptom | Primary Suspect | Difficulty 1-5 |
|---|---|---|
| Stops during spin | Inverter board | 3 |
| No motor response | Inverter board | 3 |
| Error persists after reset | Inverter board | 4 |
GE Profile 353 Inverter Board Degradation Causes
The inverter board regulates power delivery to the motor in the GE Profile washer dryer combo. Heat buildup and capacitor degradation inside the board cause signal loss over time. Power surges from household lines accelerate wear on the internal circuits. A failed board prevents the motor from receiving consistent drive signals. Replacement restores normal operation once the old unit is removed.
GE Profile 353 Inverter Board Replacement Process
Disconnect power supply to the GE Profile washer dryer combo at the breaker before any work begins. Remove the rear access panel with a screwdriver to expose the inverter board location. Unplug all wire harnesses from the board terminals while noting their positions for reinstallation. Unscrew the mounting bolts that secure the board to the chassis frame. Install the new inverter board by aligning the mounting holes and tightening the bolts evenly. Reconnect the wire harnesses in their original order to ensure proper signal flow.
Measure Output Voltage from Board
Technicians check voltage levels at the inverter board terminals on the GE Profile washer dryer combo to verify operation. The board should produce steady output between 120 and 240 volts depending on the cycle selected. Low or fluctuating readings indicate internal component failure that requires full replacement. Use a multimeter set to AC voltage for accurate results during this test. Consistent readings after installation confirm the repair succeeded.
Inspect Motor Wiring for Damage
Wiring between the inverter board and motor on the GE Profile washer dryer combo can develop breaks or corrosion. Pull back the protective sheathing along the harness to examine each conductor for nicks or burns. Clean any corroded terminals with electrical contact cleaner and a soft brush. Replace damaged sections of wire with matching gauge material if breaks appear. Secure all connections with zip ties to prevent future movement during operation.
GE Profile 353 Inverter Board Number Verification
The replacement inverter board for the GE Profile washer dryer combo must match the original part number exactly. Mismatched boards fail to communicate with the control system and trigger the same fault code again. Compare the printed number on the old board against the new unit before installation. Test fit the board in the mounting location to ensure connector alignment matches the harness layout. This step prevents return trips for incorrect parts.
GE Profile 353 Inverter Board Sourcing
After identifying fault code 353 on the GE Profile washer dryer combo the next step requires sourcing a suitable inverter board replacement. Owners should verify the exact model compatibility before purchasing from authorized suppliers or reputable parts distributors. This approach helps avoid mismatched components that could prolong the diagnostic process.
Order the correct inverter board assembly for the GE Profile washer dryer combo from an authorized supplier. Verify compatibility with the specific model series before completing the purchase. Keep the old board as a reference during the swap process.
Hey, I’m Jake. I focus on cooling systems at Appliance Mastery, like fridges, freezers, and air conditioners.
I’ve worked in appliance repair for more than ten years and I’m certified through NASTeC. I’ve seen just about every fridge issue you can imagine.
My goal is to help you fix problems without stress. Whether it’s a freezer that won’t cool or an AC that keeps beeping, I’m here to walk you through it.