The GE UltraPro 4 Device Universal Remote requires specific control codes to sync properly with televisions and other electronics. These codes allow full operation of multiple devices through a single remote unit.
Owners should locate the correct codes for their brands before beginning the programming sequence. This process ensures reliable signal transmission without interference from other remotes. Proper entry prevents common setup errors that lead to unresponsive devices.
GE UltraPro Remote Master Code Table
The GE UltraPro 4 Device Universal Remote stores hundreds of preset codes for common electronics brands. Users must match their device brand to the correct numeric sequence during initial setup. This table aggregates verified codes from manufacturer cross references for quick reference. The data covers major categories like televisions and cable boxes. Accurate selection reduces repeated programming attempts.
| Device Type | Brand | Code Options |
|---|---|---|
| Television | Samsung | 0105 0077 0076 |
| Television | LG | 0004 0050 0156 |
| Television | Sony | 0000 0111 0128 |
| Cable Box | Comcast | 0031 0051 0081 |
| DVD Player | Panasonic | 0170 0214 0309 |
| Soundbar | Bose | 0390 0421 0463 |
GE UltraPro Remote Compatibility by Device Age
Compatibility depends on the age and signal type of each target device. Newer smart televisions often require updated code sets while older models respond to legacy entries. The GE UltraPro remote handles infrared signals across four device slots without additional hardware. Testing multiple codes from the table improves success rates for mixed brand setups. Owners should note any partial functionality after initial entry.
GE UltraPro Remote Code Entry Process
Preparation involves gathering device model numbers and clearing the remote memory first. Position the GE UltraPro remote within three feet of the target device during programming. The process uses a standard setup button sequence followed by code input. Multiple attempts may be needed if the first code fails to produce a response. Keep spare batteries nearby to avoid interruptions.
Gather device manuals for brand confirmation.
Clear existing codes by holding the setup button.
Enter the four digit sequence from the table.
Test power and volume functions immediately.
GE UltraPro Sync Failure Diagnosis
Sync failures usually trace to incorrect code selection or weak battery voltage. The remote may enter a locked state after several failed attempts. Reset the unit by removing batteries for thirty seconds before retrying. Check for obstructions between the remote and device sensor. Persistent issues often require switching to an alternate code from the same brand row.
Battery Management In GE UltraPro Remotes
The GE UltraPro remote operates on two AAA batteries that last approximately six months under normal use. Low voltage causes erratic code transmission and incomplete syncs. Replace batteries before major programming sessions to maintain consistent signal strength. Store spare sets in a cool dry location to prevent leakage. Monitor performance after battery changes to confirm restored function.
GE UltraPro Four Slot Device Programming
Assign each device type to one of the four available slots on the GE UltraPro remote. Complete one device sync before moving to the next to avoid cross interference. Use the device mode buttons to switch between programmed units during daily operation. Verify all functions work across slots after full setup. Reprogram individual slots if one device loses response over time.
Perform Final GE UltraPro Sync Verification
After entering the appropriate codes from the manual into your GE UltraPro remote, it is essential to confirm that the synchronization process has completed successfully. Test each of the four devices individually. Verify that commands transmit without delay or error to ensure reliable operation across all connected equipment.
Test every assigned function on each device after all codes are entered. Confirm power volume and input selection respond correctly from the remote. Store the code list for future reference in case of memory loss.
Hey, I’m Jake. I focus on cooling systems at Appliance Mastery, like fridges, freezers, and air conditioners.
I’ve worked in appliance repair for more than ten years and I’m certified through NASTeC. I’ve seen just about every fridge issue you can imagine.
My goal is to help you fix problems without stress. Whether it’s a freezer that won’t cool or an AC that keeps beeping, I’m here to walk you through it.